Autowatch Ghost Immobiliser Installation
The Ghost is the UK’s most advanced aftermarket immobiliser designed for CAN buses. It is discrete and does not have LED indicators or key fobs and is hidden within the wiring of the vehicle.
It also allows the user to turn off the system temporarily through Transport Mode to use it when they are renting out their vehicle. This guide will take you through the steps of installing a Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser protects your car from key cloning attacks, hacking attacks and relay attacks. The system links directly to your car's ECU and is protected by a unique pin code that you choose. It is not detected by thieves using diagnostic scanners or other modern methods. It cannot be disabled with circuit cuts.
The system is simple to use, however professional installation is recommended to ensure a smooth connection with the ECU of your vehicle. Installers approved by Thatcham can assist with the installation and programing of your Ghost system. They can also recommend an alarm or tracking system to complete the protection package for your vehicle.
The first step is to disconnect the battery to prevent the possibility of airbag deployment and short circuits. After that www.g28carkeys.co.uk is now able to begin work. Basic hand tools can be used for precise connections. A multimeter can be used to check electrical values. Insulation tape and cable tie are vital to secure connections and ensure that wiring is neat. The Ghost Immobiliser user manual will provide specific guidelines specific to your particular model.
It is crucial to select a grounding location that is free of dirt or paint during installation. The installer must be sure that the immobiliser's H and CAN L wires are connected to the appropriate ports on the vehicle's ECU. These wires can be connected or soldered, depending on the model. A high-quality connector is recommended to ensure a sturdy and reliable connection.
Transport Mode can be activated by the customer once the installation is complete. This allows the vehicle to be used by valet parking or mechanics without needing to know the pin code. To accomplish this, the customer must press the button for service on the dashboard 5 times in a matter of 2 seconds. After that the system will confirm with 5 signal indicators.
The Autowatch Ghost 2 is a highly effective immobiliser that's TASSA certified and Thatcham approved. It's a great choice for those who rent their vehicles frequently on platforms such as Turo. Immobilisers can lower insurance rates, as it decreases the likelihood of theft.
Getting Started
If you are seeking a solution to protect your vehicle from thieves, you can't go wrong with an autowatch ghost immobiliser. It protects your vehicle from being started even the theft or copies the key. It's possible because of its advanced technology that stops the engine from starting until the correct PIN code is entered.
The device connects to the CAN bus network of your vehicle and allowing it to communicate with the ECU directly. It uses buttons that are already present on the dashboard and the steering wheel to create a unique sequence only you know, making it impossible for someone else to start your vehicle. This is the best way to protect your pride and joy. It will not lose its value should you ever decide to sell it.
Installing a ghost immobiliser is an easy process, however, it's important to follow the directions carefully to avoid issues with electricity and system malfunctions. First, you need to locate and determine a constant 12V power source as well as a good grounding point on the vehicle's chassis. Then, you'll be able to begin connecting the wires to the immobiliser. Make sure to use high-quality connectors and soldering techniques to ensure a secure connection. Connect the connections with heat shrink tubing, insulation tape or other materials to prevent short circuits in electrical power.
After the wires have been connected, you can connect the battery and then turn on the engine to test the immobiliser's functionality. If everything is functioning properly you can place it in a safe location beneath the dash or anywhere else in the vehicle. Be sure to cover it in a secure manner to prevent a thief from tampering with it.
The Ghost 2 immobiliser is TASSA (Tracker and Aftermarket Security System Association) certified this means it complies with the highest standards of security and is an excellent deterrent to car thieves. It offers superior protection against key cloning, hacking, and relay attacks, and it cannot be disabled without knowing the code. The device is simple to use, and can be set up to an option for a service valet so that your vehicle won't be activated when you take it for an MOT or servicing.
Wiring
The Ghost Immobiliser is a cutting-edge security system that is designed to prevent vehicle theft. It connects directly to your car's CAN bus network and communicates with the ECU which makes it virtually undetectable as an addition to your vehicle. Unlike other aftermarket systems that require the removal of circuit components, the Ghost Immobiliser doesn't interfere with the factory settings for your vehicle.
It's also totally undetectable by thieves using diagnostic scanning devices. The system doesn't send or receive radio frequency signals, but instead uses CAN data for communication with your ECU. It doesn't require any modifications to your current key fobs.
To use the Ghost Immobiliser, simply switch on the ignition of your car and then enter the sequence to disarm (either one or two buttons). The indicator will flash twice to verify that you have entered the correct code. After that, you are able to start your vehicle and drive off in peace.
Once installed Once installed, the Ghost Immobiliser will secure your vehicle from hacking and key cloning, while protecting the value of your most prized possession. If you have to surrender your vehicle for service or valet parking The Ghost Immobiliser will be temporarily disabled in Transport Mode.
You'll require a constant power source (12V) and a grounding source to complete the installation of the Ghost immobiliser. Be sure that both are well-insulated and can be touched. It is also recommended to use cable ties to bundle and secure the wires, as this will reduce the risk of tampering by potential thieves. To avoid mistakes, make sure to double-check these points and mark them using a label or tape. It's important to inspect all connections for signs of wear and tear. Make sure that all connections are firmly in place, and properly insulated. Don't forget to test your Ghost Immobiliser after installation has been completed. This will ensure that the unit is operating properly and that all connections are safe and well-insulated. Be sure to fix any issues immediately.
Testing
The Autowatch Ghost Immobiliser is a cutting-edge car security system that is integrated into your vehicle's ECU to prevent the engine from starting without authorization. Its innovative technology safeguards your vehicle from hacking and key cloning as well as other common methods employed by thieves to steal cars. The Ghost also works in conjunction with existing alarm and tracking systems to offer the ultimate vehicle protection. The Ghost's unparalleled features and secluded design make it a preferred choice for car enthusiasts and security-conscious drivers too.
It is crucial to follow the procedures for installation to ensure the complete integration of the Ghost Immobiliser. Check the wiring diagram of the vehicle to help you locate and connect the wires. You'll need to determine the power and grounding sources. Once you have located them, you will have to mark them so that they are easily identifiable when installing. It is essential to use top-quality materials and tools. Hand tools are a must with making precise connections while a multimeter can check electrical values and ensure safety. Cable tie and insulation tape ensure that all connections are neat. Finally, a user manual will give specific guidelines tailored to your Ghost model.
Before beginning the installation it is essential to test the system by entering the PIN code and starting the vehicle. This step will confirm that the immobiliser functions as intended, preventing unauthorised vehicle starts. This procedure should be carried out regularly as part of your routine inspections of your vehicle to ensure that the system is always working correctly.
Once the installation is complete Once the installation is complete, you can drive your vehicle with confidence. The Ghost will safeguard your car from thieves who might steal your car. It will ensure that no one will escape with your car even if they don't have the correct PIN code. The Ghost can also be used with a Thatcham-approved tracker to detect any attempt to steal or tamper and allow you to track your vehicle in the event of it being stolen.
The Ghost is compatible with a range of automobiles, including those from the majority of major manufacturers. If you are interested in protecting your car with this innovative device, contact Monty's Locksmith today to learn more about our installation and maintenance options. We are a TASSA Installer who is registered This certification ensures that we follow strict guidelines and procedures for installing our products. This ensures customers as well as insurance companies and law enforcement agencies that all installations are performed safely and properly.